Iron(III) oxide superfine grinding solution

2017-04-28

Iron(III) oxide or ferric oxide is the inorganic compound with the formula Fe2O3. It is one of the three main oxides of iron, the other two being iron(II) oxide (FeO), which is rare, and iron(II,III) oxide (Fe3O4), which also occurs naturally as the mineral magnetite. As the mineral known as hematite, Fe2O3 is the main source of iron for the steel industry. Fe2O3 is ferromagnetic, dark red, and readily attacked by acids. Iron(III) oxide is often called rust, and to some extent this label is useful, because rust shares several properties and has a similar composition. To a chemist, rust is considered an ill-defined material, described as hydrated ferric oxide.

The overwhelming application of iron(III) oxide is as the feedstock of the steel and iron industries, e.g. the production of iron, steel, and many alloys.

A very fine powder of ferric oxide is known as "jeweler's rouge", "red rouge", or simply rouge. It is used to put the final polish on metallic jewelry and lenses, and historically as a cosmetic. Rouge cuts more slowly than some modern polishes, such as cerium(IV) oxide, but is still used in optics fabrication and by jewelers for the superior finish it can produce. When polishing gold, the rouge slightly stains the gold, which contributes to the appearance of the finished piece. Rouge is sold as a powder, paste, laced on polishing cloths, or solid bar (with a wax or grease binder). Other polishing compounds are also often called "rouge", even when they do not contain iron oxide. Jewelers remove the residual rouge on jewelry by use of ultrasonic cleaning. Products sold as "stropping compound" are often applied to a leather strop to assist in getting a razor edge on knives, straight razors, or any other edged tool.

Iron(III) oxide is also used as a pigment, under names "Pigment Brown 6", "Pigment Brown 7", and "Pigment Red 101". Some of them, e.g. Pigment Red 101 and Pigment Brown 6, are Food and Drug Administration (FDA)-approved for use in cosmetics. Iron oxides are used as pigments in dental composites alongside titanium oxides.

Iron(III) oxide was the most common magnetic particle used in all types of magnetic storage and recording media, including magnetic disks (for data storage) and magnetic tape (used in audio and video recording as well as data storage). However, modern magnetic storage media - in particular, the hard disk drives - use more advanced thin film technology, which may consist of a stack of 15 layers or more.

Because its bandgap (1.9-2.2 eV) lies in an intense region of the solar spectrum, α-Fe2O3 has been studied as a photoanode for solar water oxidation. However, its efficacy is limited by a short diffusion length (2-4 nm) of photo-excited charge carriers and subsequent fast recombination, requiring a large overpotential to drive the reaction Research has been focused on improving the water oxidation performance of Fe2O3 using nanostructuring, surface functionalization, or by employing alternate crystal phases such as β-Fe2O3.

A mixture of zinc oxide with about 0.5% iron(III) oxide is called calamine, which is the active ingredient of calamine lotion.


stone crusher

The ACM/A series are highly efficient super-fine punch-action mechanical micro grinding machines of performing the complete process of Iron(III) oxide grinding, separation and making of the finished product within the same tightly integrated system.

1. Built-in separation mechanism-preventing over-grinding.

2. Able to produce uniform granules of required sizes by adjusting the speed of the stage-separation wheel(s) or by adjusting the strength of the blower(s).

3. Powerful blowing and strong self-cooling capability, suitable for grinding heat-sensitive materials.

4. Different grinding accessories/devices are used according to the hardness of the material being ground; different types of materials (alloyed carbon steel, stainless steel, ceramics etc) are available for the Machine's inner linings and product extracting system, meeting the needs of different industries.

5. Both manual and programmable auto-controlled machines available.

The machine is suitable for super-fine grinding of various types of brittle materials. Material hardness (Mohs scale)<4, moisture contents<10%, input size 5-200mm (as decided by the model of the machine and material hardness). The machine is widely used coating materials and other industries.

1. Our design idea is market-oriented and its goal is to increase customers’ satisfaction. Design according to the customers’ special requires. Achieve the perfect combination of rational investment and lower cost.
2.  According to related national standard strictly, we guarantee stable and reliable product quality with superb technique and technology.
3.  Control the production and examination of the parts and the whole machine strictly.
4.  The period of quality guarantee of the equipment is one year, but the whole machine is maintained for whole life. If we receive complaint from customers, we will respond immediately. And if necessary, we will send someone to the field at once.
5.  When technical breakthrough and improvement happen, we will do the correction and upgrade for customers with cost price only if customers will.
6.  Supply the blueprint of the product line and equipment details for free.

http://www.flcrusher.com

本网站由阿里云提供云计算及安全服务 Powered by CloudDream